Dimensions
D1073S SIL 2 Temperature Signal Converter
Ürün Özellikleri
- 🔹 SIL2 / SC2 Uyumlu
- 🔹 Zone 0 (Zone 20), Division 1 Giriş · Zone 2, Division 2 Kurulum
- 🔹 mV, Termokupl, RTD Veya Transmitting Potansiyometre Giriş Sinyali
- 🔹 RTD Hat Direnci Telafisi Programlanabilir
- 🔹 Referans Bağlantı Telafisi Otomatik Veya Sabit (Programlanabilir)
- 🔹 0/4-20 mA, 0/1-5 V, 0/2-10 V Çıkış Sinyali · Sıcaklık Doğrusal veya Ters
- 🔹 Her Kanal İçin 16 Karakter Etiket Tanımı
- 🔹 İki Bağımsız Trip Rölesi
- 🔹 Burnout Tespiti İçin Çıkış
- 🔹 Power Bus Enclosure Kullanımıyla Ortak Burnout Tespiti
- 🔹 Yüksek Doğruluk · Mikroişlemci Kontrollü A/D Dönüştürücü
- 🔹 Üç Port İzolasyonu: Giriş / Çıkış / Besleme
- 🔹 EMC Uyumluluğu: EN61000-6-2 · EN61000-6-4
- 🔹 Tamamen Programlanabilir Çalışma Parametreleri
- 🔹 250 Vrms (Um) Maksimum İzin Verilen Gerilim
🟡 Spare-Only
Sonraki Durum: Obsolete (31.12.2025)
Sonraki Durum: Obsolete (31.12.2025)
Connections
Description
| Type | Description |
|---|---|
| Supply Voltage | 12-24 Vdc nom (10 to 30 Vdc), reverse polarity protected, ripple within voltage limits ≤ 5 Vpp. |
| Current Consumption | 45 mA typical with 20 mA output. |
| Power Dissipation | 1.0 W with 24 V supply and 20 mA output typical. |
| Max. Power Consumption | 1.4 W at 30 V and overload condition with PPC1090 connected. |
| Input Type | Millivolt, Thermocouple (A1, A2, A3, B, E, J, K, L, Lr, N, R, S, S1, T, U), RTDs (Pt100, Pt200, Pt300, Pt500, Pt50), Ni100, Ni120, Cu types and 3-wire potentiometer. |
| Integration Time | 500 ms. |
| Output | 0/4 to 20 mA on max. 600 Ω load or 0/1 to 5 V / 0/2 to 10 V signal, current limited at 22 mA, voltage limited at 11 V. |
| Resolution | 2 μA (current), 1 mV (voltage). |
| Transfer Characteristic | Linear or reverse on mV or potentiometer; temperature linear or reverse on sensors. |
| Response Time | ≤ 50 ms (10 to 90% step change). |
| Output Ripple | ≤ 20 mVrms on 250 Ω load. |
| Input Performance | Calibration & linearity accuracy: ≤ ± 40 μV / 200 mΩ / 0.2 % or ± 0.05 % of input. Temp. influence: ≤ ± 0.01 % / °C. Ref junction compensation: ≤ ± 1 °C. |
| Analog Output Performance | Calibration accuracy: ≤ ± 0.1% FS; Linearity error: ≤ ± 0.05% FS; Temp. influence: ≤ ± 0.01% / °C on zero and span. |
| Isolation Test Voltage | I.S. In/Out & In/Supply: 1.5 KV; In/In & Out/Out & Out/Supply: 500 V. |
| Environmental Conditions | Operating: -20 to +60 °C, max 90% RH non-condensing up to 35 °C. Storage: -45 to +80 °C. |
| Safety Parameters | Uo/Voc = 10.8 V, Io/Isc = 9 mA, Po/Po = 24 mW @ terminals 13-16. Ui/Vmax = 18 V, Ci = 6 nF, Li = 0 nH. Um = 250 Vrms, -20 °C ≤ Ta ≤ 60 °C. |
| Mounting Type | EN/IEC60715 TH 35 DIN-Rail. |
| Weight | About 140 g. |
| Connection | By polarized plug-in disconnect screw terminal blocks to accommodate terminations up to 2.5 mm². |
| Location | Safe Area or Zone 2, Group IIC T4, Class I, Division 2. |
| Protection Class | IP 20. |
| Dimensions | Width 22.5 mm, Depth 99 mm, Height 114.5 mm. |
| Features | SIL2/SC2, input from Zone 0/Division 1, output duplication, trip amplifiers, burnout detection, µP-controlled, fully programmable, EMC EN61000-6-2 / EN61000-6-4 compliant. |
| Status | SPARE-ONLY – Next: OBSOLETE (2025-12-31) |
Additional information
| GMI-Applications | Load Cell Input |
|---|---|
| SIL Seviyesi | SIL 2 |
