| Supply Voltage | 12-24 Vdc nom (10 to 30 Vdc) reverse polarity protected, ripple within voltage limits ≤ 5 Vpp. |
| Supply Current Consumption | 45 mA with 20 mA output typical |
| Supply Power Dissipation | 1.0 W with 24 V supply voltage and 20 mA output typical. |
| Supply Max. power consumption | at 30 V supply voltage, overload condition and PPC1090 connected, 1.4 W |
| Input Type | 0/4 to 20 mA (-4 to +24 mA reading) separately powered input, voltage drop ≤ 0.5 V or 0/1 to 5 V or 0/2 to 10 V (-2 to +12 V reading) 1 MΩ impedance. |
| Input Integration time | 100 ms. |
| Input Resolution | 1 µA on current input, 1 mV on voltage input. |
| Input Visualization | 1 µA on current input, 1 mV on voltage input. |
| Input Input range | -4 to +24 mA on current input, -2 to +12 V on voltage input. |
| Burnout Type | enabled or disabled. Analog output can be programmed to detect burnout condition with downscale or highscale forcing. |
| Burnout Range | low and high separated trip point value programmable between -5 to +25 mA on current input and -3 to +13 V on voltage input. |
| Output Type | 0/4 to 20 mA, on max. 600 Ω load source mode, current limited at 22 mA or 0/1 to 5 V or 0/2 to 10 V signal, limited at 11 V. |
| Output Resolution | 2 µA current output or 1 mV voltage output. |
| Output Transfer characteristic | linear or reverse. |
| Output Response time | ≤ 50 ms (10 to 90 % step change). |
| Output Output ripple | ≤ 20 mVrms on 250 Ω load. |
| Input performance Type | Ref. Conditions 24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature. |
| Input performance Calibration and linearity accuracy | ≤ ± 20 µA on current input or ≤ ± 10 mV on voltage input. |
| Input performance Temperature influence | ≤ ± 2 µA, 1 mV of input for a 1 °C change. |
| Analog output performance Calibration accuracy | ≤ ± 0.1 % of full scale. |
| Analog output performance Linearity error | ≤ ± 0.05 % of full scale. |
| Analog output performance Supply voltage influence | ≤ ± 0.05 % of full scale for a min to max supply change. |
| Analog output performance Load influence | ≤ ± 0.05 % of full scale for a 0 to 100 % load resistance change |
| Analog output performance Temperature influence | ≤ ± 0.01 % on zero and span for a 1 °C change. |
| Isolation Test Voltage | I.S. In/Out 1.5 KV; I.S. In/Supply 1.5 KV; I.S. In/I.S. In 500 V; Out/Supply 500 V; Out/Out 500 V. |
| Environmental conditions Operating | temperature limits -20 to + 60 °C, relative humidity max 95 %. |
| Environmental conditions Storage | temperature limits -45 to + 80 °C. |
| Safety description Safety parameters | Uo/Voc = 10.8 V, Io/Isc = 4 mA, Po/Po = 11 mW at terminals 14-15-16, 10-11-12. Ui/Vmax = 30 V, Ci = 4.5 nF, Li = 0 nH at terminals 14-15-16, 10-11-12. Um = 250 Vrms, -20 °C ≤ Ta ≤ 60°C. |
| Mounting Type | EN/IEC60715 TH 35 DIN-Rail. |
| Mounting Weight | about 140 g |
| Mounting Connection | by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm2. |
| Mounting Location | Safe Area/Non Hazardous Locations or Zone 2, Group IIC T4, Class I, Division 2, Groups A, B, C, D Temperature Code T4 and Class I, Zone 2, Group IIC, IIB, IIA T4 installation. |
| Mounting Protection class | IP 20 |
| Mounting Dimensions | Width 22.5 mm, Depth 99 mm, Height 114.5 mm. |
